Stainless Steel Handrail Tube Square
Stainless Steel Handrail Tube Square
Stainless Steel Handrail Tube Square
Stainless Steel Handrail Tube Square

Stainless Steel Handrail Tube Square

TBE.SQU.157.3

Regular price $68.18 Sale price $54.54 Save 20%
/
Shipping calculated at checkout.

Size
Only 4999 items in stock!

Stainless Steel Square Tube is usually used as a handrail or top rail for our railing systems. Tubes are available by the foot from 3 feet up to 19.7 feet.

  • Made of corrosion-resistant ANSI 316 Stainless Steel Marine Grade to give the best possible performance for years to come
  • Dimension: 1.57x1.57" (40x40mm)
  • Tube Thickness: 0.102" (2.6mm or gauge 12)
  • Finish: Satin Brushed Finish

This tube can be used in a variety of applications including, but not limited to

  • Hand railing
  • Foot (bar) railing
  • Queuing railing
  • Pony rail (mounted on top of a wall)
  • Bathroom vanities
  • Shelving systems

Lengths over 7.5 feet need to be shipped by LTL.
Please contact sales at (425) 405-4405 for a Shipping quote.

Image GalleryProjects Gallery

These directions will assist the user in properly cutting stainless steel tubes.

Inline Design recommends using a cold saw, band saw, preferably oil-fed. These saws will leave minimal burr and no heat marks. For round tubing, use 65S Stainless Steel Pipe Cutters.

For demonstration purposes, Inline Design is providing directions based on the use of the cut-off saw.

Caution: Wear protective ANSI-approved safety glasses, work gloves, and masks all the time.

Tools Required

  1. Cut-off saw
  2. Duct tape
  3. Abrasive disk/blade
  4. Paper towel
  5. Disk sander
  6. Inner/outer reamer tool*

Instructions

  1. Place duct tape on the clamp of the cut-off saw and to all other areas where the tube will touch the metal to protect the surface from getting scratched while being cut
  2. Mark cutting point, clamp the tubing in place, and commence the cut
  3. Immerse the cut end into water to cool the cut tube
  4. File any sharp edges evenly with a fine metal file
  5. Clean the tube using a paper towel and some household cleaner
  6. Note: if necessary, ream/deburr the outside and inside of the tube. Be careful not to scratch the tubing while deburring; keep the deburr tool straight
  7. To polish the cut, follow instructions for maintaining stainless steel surface

NOTE: A small amount of surface corrosion is not uncommon after exposure to weather or salty conditions. We recommend using our passivation solution to prevent any surface corrosion from happening; more information is available on our Engineering Specifications Page.

Downloads

PDF Instructions

Overview

This document contains the comprehensive information for how to drill and tap holes for brackets use or handrail brackets

Caution: Wear protective ANSI approved safety glasses, working gloves and breathing mask at all times • Inspect before installation or use; do not use if parts are loose or damaged

Tools Required

    1. Center Punch
    2. Hand drill
    3. Drill bit
    4. Tap bit
    5. Cutting oil
    6. Marker Pen

Guide Bit and Tab Guide

Bracket/Screw Drill Size ANSI Size Tap Size
Pyramid 5mm 3/64" M6 x 1
Cone 4mm 5/32" M5 x 0.8
HBWA.005 5mm 3/64" M6 x 1
HBWA.006 5mm 5/32" M5 x 0.8
HBWA.008 4mm 5/32" M5 x 0.8
HBWA.009 4mm 5/32" M5 x 0.8
HBWA.010 4mm 5/32" M5 x 0.8
HBWA.011 4mm 5/32" M5 x 0.8
HBWA.012 4mm 5/32" M5 x 0.8
HBWA.013 4mm 5/32" M5 x 0.8
HBWA.014 4mm 5/32" M5 x 0.8
HBWA.015 4mm 5/32" M5 x 0.8
HBWA.016 4mm 5/32" M5 x 0.8
M8 6.9mm 17/64" M8 x 1.25

Instructions

  1. Mount the posts to the floor or the brackets to the wall before installing the handrail tube. Please refer to other instructions document found on our website for help in that operation
  2. Place the handrail tubing on the saddles. Mark the drilling points using a marker
  3. It’s very important not to skip this point otherwise the drill bit will skid. Remove the handrail then place it on a working table. Mark the drilling points with a center punch. Repeat this several times in the same location to give a good guide for the drill bit.
  4. Use the corresponding drill bit size shown in table above.
  5. Apply cutting fluid on the drill bit.
  6. Hold firm but without pressing too hard the hand-drill then gradually apply pressure to drill through the top rail with stopping a couple of times to reapply the cutting fluid. Complete all marked location.
  7. Replace the drill bit with the corresponding tap bit shown in table.
  8. Apply cutting fluid on the tap. Tapping is to be done at a slower speed then drilling. Start at a slow speed then increase the speed once the tap catches a couple of threads.
  9. Reverse the direction of the drill to remove the tap remembering to carefully keep the tap bit straight.

Downloads:

PDF Instructions

Use for intended purposes only It is the responsibility of Inline Design customers to comply with city, national, and international building codes. Please ensure proper research is conducted prior to the installation due to variations of city building codes. Inline Design is not liable for ensuring that projects meet code requirements


    Recently viewed